The Wavy Knit Waterproof Recliner Cover: Stretch Knit Polyester Chair Cover in 10 Colors for 1 Seater Recliners 27-38 in Wide and 40-50 in Tall

Specifications

Fabric: Stretch knit polyester, about 200 gsm
Texture: Soft knit with a raised wavy pattern
Fits: Recliners 27-38 in (68-100 cm) wide across the back, 40-50 in (100-127 cm) tall
Washing: Machine wash at 30°C (86°F) on a gentle cycle, then air dry
In the box: 1 cover
Good to know: One cover fits one recliner
Seat depth: Up to 24 in (60 cm)
Colors: Gray, beige, light gray, cypress green, ivory, blue, wine red, coffee, navy, jade
Waterproof: Yes

What this cover is

The Wavy Knit Waterproof Recliner Cover is a single stretch knit polyester cover, about 200 gsm, with a soft hand and a raised wavy pattern that adds quiet texture to your chair. It is waterproof, so spills and drips stay on the surface instead of soaking in. The knit stretches in both directions, which lets it follow the shape of your recliner rather than sitting on top like a loose throw.

This is a practical layer for a recliner you use every day. It guards against dust, crumbs, pet hair and the small accidents that add up. The fabric is plain in style and solid in color, so it works with most living room, office or den setups.

Sizes and fit

One size covers most standard recliners. Check your chair against these numbers before you order.

Measurement	Range
Width across the back	27 to 38 in (68 to 100 cm)
Height	40 to 50 in (100 to 127 cm)
Seat depth	Up to 24 in (60 cm)

This listing is for the 1 seater size. One cover fits one recliner. If your chair falls inside these ranges, the stretch knit should pull over the back, arms and seat and tuck in around the cushions.

Colors

Pick the tone that suits your room:

Dark gray
Beige
Light gray
Sage green
Ivory
Teal blue
Burgundy
Dark brown
Navy blue
Teal green

Neutrals like Ivory, Beige and Light gray keep things calm. Sage green, Teal blue and Teal green add a softer color note. Burgundy, Dark brown, Navy blue and Dark gray ground a room with deeper tones.

How to put it on

Start with the recliner fully upright and closed. Slip the cover over the back first, then work it down over the arms. Pull the front edge over the seat and press the fabric into the gap between the seat and the arms so it holds. Smooth the knit with your hands from the center outward. The stretch does the rest.

Because the fabric stretches, you can adjust it after a few minutes of use. If a corner lifts, tuck it back in. The cover moves with the recliner mechanism, so you can still raise the footrest and lean back without removing it.

Care

Machine wash at 30°C (86°F) on a gentle cycle. Air dry. Do not wring or twist the knit, and keep it out of a hot dryer to protect the stretch and the waterproof finish. Most light marks wipe off with a damp cloth between washes.

Good to know

Fabric: stretch knit polyester, about 200 gsm
Texture: soft knit with a raised wavy pattern
Waterproof: yes
In the box: 1 cover
One cover fits one recliner
Machine wash at 30°C (86°F), gentle cycle, air dry

Questions

Will this fit my recliner?

It fits recliners 27 to 38 in (68 to 100 cm) wide across the back and 40 to 50 in (100 to 127 cm) tall, with seat depth up to 24 in (60 cm). Measure your chair at those points before ordering. The stretch knit follows the shape of the chair.

Is it really waterproof?

Yes. The knit polyester is waterproof, so spills and drips stay on the surface. Wipe them up with a damp cloth and the cover is ready to use again.

Can I keep it on while I recline?

Yes. The stretch fabric moves with the recliner, so you can raise the footrest and lean back without taking the cover off. Tuck the front edge into the seat gap for a snug hold.

How do I wash it?

Machine wash at 30°C (86°F) on a gentle cycle, then air dry. Avoid a hot dryer so the stretch and waterproof finish stay intact.